Categories

SHANGHAI JIANGTONG INTERNATIONAL TRADING CO., LTD

Tel:+86-21-50688657

Fax:+86-21-50688657

E-mail:
sales@epdmrubberflooring.com

Home > Exhibition > Content

INSTALLATION

In recent years, the rubber floor is more and more popular with everyone, so we should pay more attention to the paving. How do the rubber floor be laid? Let's tell you the rubber floor paving method below.

image.png

Construction process: grass-roots treatment -- elastic line finding rules -- blending agent -- rubber board cleaning - brush glue - sticking ground -- rolling - stickup rubber kicking


1, basic level processing: Grassroots ground cement plaster, the surface should be smooth, hard, dry and free of grease and other impurities (including sand). If there are pits should adopt 107 glue cement putty repair, repair after brushing a water emulsion, which increases the overall strength.


2, playing the line to find the rules: in the room length and width direction elastic cross centre line (or the diagonal line), the line is to be thin and clear. If the specifications of the rubber plate and the length and width of the room are not equal to the modulus, the edge line should be ejected along the ground. When the drawing is required, the position line of the drawing shall be ejected in advance. And test the layout according to the template. After the rubber ground is laid, the height of the kicking board is upwards, and a block is attached to each end of the wall.


3, blending adhesive: the raw material should be inspected by a special person before the ingredients, such as the discovery of XY401 glue, discoloration and impurities. The glue diluted diluent also with the mix with the use, storage interval should not exceed 1 hours, the mixing, transportation and storage of used rubber or enamel containers, prohibited the use of iron, to prevent the occurrence of chemical reactions, color glue,


4, rubber plate cleaning: to ensure firmly bonded back to remove the rubber sheet packing brush glue, use clean cloth cleaning brush, the rubber plate behind the dust and talcum powder detergent, to ensure that the bond effect.

image.png

5, brush: first, brush a thin and even combination of base glue. The mixing ratio of base glue and solvent diluent is XY401 glue: xylene = 100:100 ~ 150.


6, laying rubber sheets: cross laying and diagonal paving. The construction temperature should not be below 10 C when the adhesive is applied to the rubber sheet. If the temperature is lower than the above temperature, measures should be taken to ensure the bonding quality. Paste rubber floor, from the cross line to paste, will be back on the rubber plate, with 3 sub brush along the back brushing the ground rubber plate and rubber paste board a glue, the glue should be slightly diluted, the ratio of XY401: 100:10 or 120# have been using xylene; gasoline: ethyl acetate instead of =100:200. Glue to brush, thin and uniform without leakage. After the glue dry brush slightly sticky is appropriate, according to play Moxian paving, and then along the side of the rubber board paved with roller compaction, and then the second plate paving rolling roller, in turn. Rubber plate butt paving, nuiko must achieve vertical and horizontal, cross stitch at nuiko without skew, linking closely, the gap is uniform.


7, lay the rubber skirting board: after the ground is paved, play the skirting line of the skirting kick, and paste the skirting board at the two ends of the room respectively, then hang up the line and paste. First, we should lay the Yin Yang corner, then lay the large surface and roll it repeatedly. Pay attention to the rolling of the Yin angle of the upper mouth of the foot plate and the kicking board and the ground.

image.png

8, polishing wax: paving rubber floor and skirting, mop clean, dry, and then use the bag wrapped polishing soft wax prepared, coated with 1 ~ 2 times (weight ratio of soft wax: gasoline = 100:20 ~ 30), the other with 1% to 3% floors with the same color pigment. Wipe it with a net cloth until the surface is smooth and bright.

image.png

Previous: No Information

Next: No Information